OCAP Setup

OCAP Details

 New
# Application Name Ocap Name Description Step Created By Created Time Last Updated By Last Updated Time  
1 PCS OCAP 1 OCAP 1 1. Clean Socket 2. Swap Socket PuiPui 20/07/2020
03:22:07 PM 		11/10/2020
08:49:51 PM
2 PCS OCAP 2 OCAP Testing 2 1. Please input the relevant data PuiPui 20/07/2020
03:22:07 PM 		14/09/2020
03:22:02 AM
3 PCS OCAP 6 1. Change sockets 2. Remove socket and send for PM or change sockets 3. Send sample units for VM inspection. make sure it pass PuiPui 20/07/2020
03:22:07 PM 		24/10/2025
03:07:19 PM
4 PCS OCAP 7 1. Check socket and device probe marks or dent 2. Clean or change socket 3. Send sample units for VM inspection. make sure it pass PuiPui 20/07/2020
03:22:07 PM 		17/09/2020
12:57:41 AM
5 PCS OCAP 8 1. Check socket and device probe marks or dent 2. Remove socket and send for PM or change socket 3. Send sample units for VM inspection. make sure it pass PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
6 PCS OCAP 9 1. Check socket condition 2. Check temp sensor test readings 3. Check handler temp setting & temperature PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
7 PCS OCAP 10 1. Check socket condition 2. Check temp sensor test readings 3. Check RX_power test readings 4. Perform GU offset calibration PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
8 PCS OCAP 11 1. Check socket condition 2. Check temp sensor test readings 3. Check RX_power test readings 4. Perform GU offset calibration PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
9 PCS OCAP 12 1. clean/change socket 2. disable site 3 \r\not 1. swap socket swp socket 2. Clean Socket \r\not PuiPui 20/07/2020
03:22:07 PM 		28/09/2020
02:25:34 PM
10 PCS OCAP 13 1. clean/change socket 2. disable site PuiPui 20/07/2020
03:22:07 PM 		16/09/2020
11:29:02 PM
11 PCS OCAP 14 1) CLEAN SOCKET 2) CHANGE SOCKET PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
12 PCS OCAP 15 1. Clean Socket 2. Change socket 3. Change load board 4. Trigger PLS/PE to check FAB issue PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
13 PCS OCAP 16 1. Clean Socket 2. Change socket 3. Change load board 4. Trigger PLS/PE to check FAB issue PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
14 PCS OCAP 17 1. Clean Socket 2. Change socket 3. Change load board 4. Trigger PLS/PE to check FAB issue PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
15 PCS OCAP 18 1) Clean socket 2) Change socket If the same result 3) Change to other good loadboard, if result the same 4) Down to TSG for tester repair PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
16 PCS OCAP 19 1) Clean socket 2) swap socket 3) change socket 3) change loadboard PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
17 PCS OCAP 20 1) Clean socket 2) Swap socket 3) Change socket 4) change loadboard PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
18 PCS OCAP 21 1. If high SB13/SB14: Delete program. Initialize tester. Reload program. 2. If still SB13/14, Change Skt or LB PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
19 PCS OCAP 22 1. If high SB20, 21, 23, 24, 29: CHECK or PM SKT 2. If still same failures, Change Skt 3. If need LB change, Endlot. Reload Pgm PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
20 PCS OCAP 23 1. If high SB20, 21, 23, 24, 29: CHECK or PM SKT 2. If still same failures, Change Skt 3. If need LB change, Endlot. Reload Pgm PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
21 PCS OCAP 24 1. If high SB20, 21, 23, 29: CHECK or PM SKT 2. If still same failures, Change Skt 3. If need LB change, Endlot. Reload Pgm PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
22 PCS OCAP 25 1. If high SB20, 21, 23, 29: CHECK or PM SKT 2. If still same failures, Change Skt 3. If need LB change, Endlot. Reload Pgm PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
23 PCS OCAP 26 1) Running Yield Below 75% PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
24 PCS OCAP 27 ### 1st action ### Clean socket ### === 2nd action === Change socket === +++ 3rd action +++ Change loadboard +++ PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
25 PCS OCAP 28 1)swap socket form good site or replace with lower insertion spare socket. If the same PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
26 PCS OCAP 29 1)swap socket form good site or replace with lower insertion spare socket. If the same result 2)Change other good loadboard, if result the same 3)Down to TSG for tester repair PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
27 PCS OCAP 30 1)swap socket form good site or replace with lower insertion spare socket. If the same result 2)If fail Bin8 t#13159/13160/23159/23160 change socket of low yield site and replace MIPOX paper also if dirty. 3)Change other good loadboard, if result the same 4)Down to TSG for tester repair PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
28 PCS OCAP 31 1)swap socket form good site or replace with lower insertion spare socket. If the same result 2)If fail Bin8 t#13159/13160/23159/23160 change socket of low yield site and replace MIPOX paper also if dirty. 3)Change other good loadboard, if result the same 4)Down to TSG for tester repair PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
29 PCS OCAP 32 1)swap socket from good site or replace with lower insertion spare socket. If the same result 2)Change other good loadboard, if result the same 3)Down to TSG for tester repair PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
30 PCS OCAP 33 2 Consecutive Fail PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
31 PCS OCAP 34 2 non Consecutive Fail!!!Pls clean socket/verify socket on the consecutive fail site. PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
32 PCS OCAP 35 <50% Yield OCAP 1.If Top failure is SPLLScreen or VRTC_PSM or AFE ADC INL test/s ABORT and call attention of PE or PLS. 2.If non of the item1 proceed to Normal OCAP (socket clean/LB change) PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
33 PCS OCAP 36 <50% Yield OCAP 1.If Top failure is SPLLScreen or VRTC_PSM or AFE ADC INL test/s call attention of PE or PLS. 2.If non of the item1 proceed to Normal OCAP (socket clean/LB change) PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
34 PCS OCAP 37 5 Consecutive conty Fail!!!Pls clean socket/verify socket. PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
35 PCS OCAP 38 5 Consecutive Fail!!!Pls clean socket/verify socket. PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
36 PCS OCAP 39 5 consecutive SB201 fallout!!! Pls clean bottom socket with Mipox and air gun blow. PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
37 PCS OCAP 40 5 consecutive SB201 fallout, pls clean the bottom socket with Mipox and air gun blow. PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
38 PCS OCAP 41 5 consecutive top socket conty fallout, pls clean the top socket with nylon brush and air gun blow PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
39 PCS OCAP 42 5 consecutive top socket conty fallout!!! Pls clean top socket with nylon brush and air gun blow PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
40 PCS OCAP 43 70% Low Yield OCAP 1. Clean Socket 2. Change socket 3. Change load board 4. Trigger PLS/PE to check FAB issue PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
41 PCS OCAP 44 70% Low Yield OCAP 1. Clean Socket 2. Change socket 3. Change load board 4. Trigger PLS/PE to check FAB issue PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
42 PCS OCAP 45 70% Low Yield OCAP 1. MTF is SB17, please clean socket 2. If after clean socket still cannot recover, please change socket 3. Change load board, must reload program and run corr 4. Trigger PLS/PE to check FAB issue PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
43 PCS OCAP 46 70% Low Yield OCAP 1. MTF is SB17, please clean socket 2. If after clean socket still cannot recover, please change socket 3. Change load board, must reload program and run corr 4. Trigger PLS/PE to check FAB issue PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
44 PCS OCAP 47 70% Low Yield OCAP 1. Please clean socket 2. If after clean socket still cannot recover, please change socket 3. Change load board, must reload program and run corr 4. Trigger PLS/PE to check FAB issue PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
45 PCS OCAP 48 70% Low Yield OCAP 1. Please clean socket 2. If after clean socket still cannot recover, please change socket 3. Change load board, must reload program and run corr 4. Trigger PLS/PE to check FAB issue PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
46 PCS OCAP 49 75% Low Yield OCAP 1. Clean Socket 2. Change socket 3. Change load board 4. Trigger PLS/PE to check FAB issue PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
47 PCS OCAP 50 75% Low Yield OCAP 1. Clean Socket 2. Change socket 3. Change load board 4. Trigger PLS/PE to check FAB issue PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
48 PCS OCAP 51 80% Low Yield OCAP 1. Clean Socket 2. Change socket 3. Change load board 4. Trigger PLS/PE to check FAB issue PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
49 PCS OCAP 52 80% Low Yield OCAP 1. Please clean socket 2. If after clean socket still cannot recover, please change socket 3. Change load board, must reload program and run corr 4. Trigger PLS/PE to check FAB issue PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
50 PCS OCAP 53 80% Low Yield OCAP 1. Please clean socket 2. If after clean socket still cannot recover, please change socket 3. Change load board, must reload program and run corr 4. Trigger PLS/PE to check FAB issue PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
51 PCS OCAP 54 85% Low Yield OCAP 1. Change Socket 2. Change socket 3. Change load board 4. Trigger PLS/PE to check FAB issue PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
52 PCS OCAP 55 85% Low Yield OCAP 1. Check / Clean or Change Socket 2. Check / Clean or Change load board 3. Trigger PLS/PE to check FAB issue PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
53 PCS OCAP 56 85% Low Yield OCAP 1. Clean Socket 2. Change socket 3. Change load board 4. Trigger PLS/PE to check FAB issue PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
54 PCS OCAP 57 8 Consecutive Fail!!!Pls clean socket/verify socket. PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
55 PCS OCAP 58 8 Consecutive Fail!!!Pls clean socket/verify socket. PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
56 PCS OCAP 59 8 Consecutive Fail!!!Pls clean socket/verify socket on the consecutive fail site. PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
57 PCS OCAP 60 8 Consecutive Fail!!!Pls clean socket/verify socket on the consecutive fail site. PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
58 PCS OCAP 61 Action #1 – DO NOT perform online socket cleaning. Send socket to HW for thorough PM/change socket Action #2 – Repeated Sbin11 after action #1 in less than 1 hour, MUST change another socket. Action #3 – Prolong Sbin11 triggering, replace load board & raise escalation to PLS/PE for further investigation. action#4. Send sample units for VM inspection. make sure it pass PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
59 PCS OCAP 62 Action #1 – DO NOT perform online socket cleaning. Send socket to HW for thorough PM/change socket Action #2 – Repeated Sbin16 after action #1 in less than 1 hour, MUST change another socket. Action #3 – Prolong Sbin16 triggering, replace load board & raise escalation to PLS/PE for further investigation. action#4. Send sample units for VM inspection. make sure it pass PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
60 PCS OCAP 63 AP: 1) Clean Socket 2) Swap / Change Socket 3) Change Loadboard 4) Tester Verification PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
61 PCS OCAP 64 Below 15% OCAP: 1)Abort lot and run corr to verify setup 2a)If corr fail on the same sbin and tests, then down setup to LSG to fix the setup first 2b)If corr pass, MFG to select other lot with different FAB ID PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
62 PCS OCAP 65 Below 15% OCAP: 1)If found MTF on T#170, continue running 2)If MTF is not TN170, run corr to verify the set up PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
63 PCS OCAP 66 Below 1% OCAP: 1)Abort lot and run corr to verify setup 2a)If corr fail on the same sbin and tests, then down setup to LSG to fix the setup first 2b)If corr pass, MFG to select other lot with different FAB ID PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
64 PCS OCAP 67 Below 20% OCAP: 1)Abort lot and run corr to verify setup 2a)If corr fail on the same sbin and tests, then down setup to LSG to fix the setup first 2b)If corr pass, MFG to select other lot with different FAB ID PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
65 PCS OCAP 68 Below 30% OCAP: 1)Abort lot and run corr to verify setup 2a)If corr fail on the same sbin and tests, then down setup to LSG to fix the setup first 2b)If corr pass, MFG to select other lot with different FAB ID PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
66 PCS OCAP 69 Below 30% OCAP: If MTF is on T#83084, continue running 1)Abort lot and run corr to verify setup 2a)If corr fail on the same sbin and tests, then down setup to LSG to fix the setup first 2b)If corr pass, MFG to select other lot with different FAB ID PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
67 PCS OCAP 70 Below 50% OCAP: 1)Abort lot and run corr to verify setup 2a)If corr fail on the same sbin and tests, then down setup to LSG to fix the setup first 2b)If corr pass, MFG to select other lot with different FAB ID PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
68 PCS OCAP 71 Below 50% OCAP: 1)Abort lot and run corr to verify setup 2a)If corr fail on the same sbin and tests, then down setup to LSG to fix the setup first 2b)If corr pass, MFG to select other lot with different FAB ID PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
69 PCS OCAP 72 Below 50% OCAP: 1)Abort lot and run corr to verify setup 2a)If corr fail on the same sbin and tests, then down setup to LSG to fix the setup first 2b)If corr pass, MFG to select other lot with different FAB ID PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
70 PCS OCAP 73 Below 50% OCAP: 1)Abort lot and run corr to verify setup 2a)If corr fail on the same sbin and tests, then down setup to LSG to fix the setup first 2b)If corr pass, MFG to select other lot with different FAB ID PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
71 PCS OCAP 74 Below 50% OCAP: 1)Abort lot and run corr to verify setup - FORCE QA LOT 2a)If corr fail on the same sbin and tests, then down setup to LSG to fix the setup first 2b)If corr pass, MFG to select other lot with different FAB ID PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
72 PCS OCAP 75 Below 70% OCAP: 1)Abort lot and run corr to verify setup 2a)If corr fail on the same sbin and tests, then down setup to LSG to fix the setup first 2b)If corr pass, MFG to select other lot with different FAB ID PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
73 PCS OCAP 76 Below 80% OCAP: 1)Abort lot and run corr to verify setup 2a)If corr fail on the same sbin and tests, then down setup to LSG to fix the setup first 2b)If corr pass, MFG to select other lot with different FAB ID PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
74 PCS OCAP 77 CALL PE/PLS PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
75 PCS OCAP 78 CAP: 1) Clean Socket 2) Swap / Change Socket 3) Change Loadboard 4) Tester Verification PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
76 PCS OCAP 79 CAP: 1) Clean Socket 2) Swap / Change Socket 3) Change Loadboard 4) Tester Verification PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
77 PCS OCAP 80 CBL OCAP: 1) Clean socket.If the same result 2) Replace with other good socket with lower insertion spare socket. If the same result 2)Change other good loadboard/DUTcard, if result the same 3)Down to TSG for tester repair PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
78 PCS OCAP 81 CBL OCAP: 1)swap socket form good site or replace with lower insertion spare socket. If the same result 2)Change other good loadboard, if result the same 3)Down to TSG for tester repair PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
79 PCS OCAP 82 CBL OCAP: 1)swap socket form good site or replace with lower insertion spare socket. If the same result 2)Change other good loadboard, if result the same 3)Down to TSG for tester repair PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
80 PCS OCAP 83 CBL or continouos failurre of Bin5 Conty 1) LSG to clean sockets and if same 2) LSG change or swap from good sites and if same 3) LSG to change the Loadboard and if same 4) Down to TSG for tester repair PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
81 PCS OCAP 84 check for device stuck PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
82 PCS OCAP 85 check for device stuck on socket PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
83 PCS OCAP 86 Check for Map shift issue PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
84 PCS OCAP 87 Check handler temperature/offset PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
85 PCS OCAP 88 Check setups, Reboot PC. OCAP: 1.Clean Socket 2.Swap Socket -- check if failure moves 3. Change Socket 4.Change Loadboard. PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
86 PCS OCAP 89 . Check socket and device probe marks or dent 2. Remove socket and send for PM or change socket 3. Send sample units for VM inspection. make sure it pass PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
87 PCS OCAP 90 Clean/Replace Socket PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
88 PCS OCAP 91 Clean/Replace Socket PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
89 PCS OCAP 92 clean socket PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
90 PCS OCAP 93 clean socket PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
91 PCS OCAP 94 Clean socket & check insertion PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
92 PCS OCAP 95 Clean sockets PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
93 PCS OCAP 96 Consecutive 10 failure PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
94 PCS OCAP 97 Consecutive Bin5 failures in one site. Please repair the setup. Send the socket for offline and thorough PM. PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
95 PCS OCAP 98 CONSECUTIVE CONTY > 5 OCAP: 1) Clean Socket 2) Swap / Change Socket 3) Change Loadboard 4) Tester Verification PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
96 PCS OCAP 99 Consecutive Fail!!!Pls clean top socket with nylon brush and botttom socket with Mipox. PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
97 PCS OCAP 100 CONSECUTIVE FAILURE > 20 OCAP: 1) Clean Socket 2) Swap / Change Socket 3) Change Loadboard 4) Tester Verification PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
98 PCS OCAP 101 Continuous Hbin3 failure. Perform OCAP. Check socket, then LB, then tester. PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
99 PCS OCAP 102 Conty over-reject. Please apply necessary OCAP. PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
100 PCS OCAP 103 CP Detected! PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
101 PCS OCAP 104 CPK Detected! PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
102 PCS OCAP 105 CP triggered!!! PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
103 PCS OCAP 106 Critcal Triggered PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
104 PCS OCAP 107 critical PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
105 PCS OCAP 108 critical PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
106 PCS OCAP 109 critical PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
107 PCS OCAP 110 critical pop up 1). check tester 2). check handler 3). check all PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
108 PCS OCAP 111 Critical! Site Yield Monitor trigger PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
109 PCS OCAP 112 Default rule:Critical! Local Site Yield Monitor PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
110 PCS OCAP 113 Default rule: critical site fail monitor PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
111 PCS OCAP 114 Default rule for local site fail monitor PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
112 PCS OCAP 115 Default rule:Warning! Local Site Yield Monitor PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
113 PCS OCAP 116 delta site yield trigger PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
114 PCS OCAP 117 Detected Piggy Back OCAP: 1) abort the lot (MS), 2) hold for PLS/PE to check (PE/PLS), 3) check handler, input/output shuttle, sticky socket/contactor and stuck units (LSG) 4) start new lot (MS) PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
115 PCS OCAP 118 Detected Piggy Back OCAP: 1) abort the lot (MS), 2) hold for PLS/PE to check (PE/PLS), 3) check handler, sticky socket/contactor and stuck units (LSG) 4) start new lot (MS) PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
116 PCS OCAP 119 Detected Piggy Back OCAP: 1) abort the lot (MS), 2) hold for PLS/PE to check (PE/PLS), 3) check handler, sticky socket/contactor and stuck units (LSG) 4) start new lot (MS) PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
117 PCS OCAP 120 Detected unit repeated tested, check setup PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
118 PCS OCAP 121 Device is Mis-trimmed : T#15708: OCAP 1)swap socket form good site or replace with lower insertion spare socket. 2)if still fail on t#15708 - SEND FOR PM OR CHANGE SOCKET/s PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
119 PCS OCAP 122 Device is Mis-trimmed : T#15708: OCAP 1)swap socket form good site or replace with lower insertion spare socket. 2)if still fail on t#15708 - SEND FOR PM OR CHANGE SOCKET/s PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
120 PCS OCAP 123 Device is Mis-trimmed : T#15708: OCAP 1)swap socket form good site or replace with lower insertion spare socket. 2)if still fail on t#18708 - SEND FOR PM OR CHANGE SOCKET/s PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
121 PCS OCAP 124 disable site PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
122 PCS OCAP 125 disable site PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
123 PCS OCAP 126 Do OCAP PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
124 PCS OCAP 127 Do OCAP PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
125 PCS OCAP 128 Down setup to LSG to change socket PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
126 PCS OCAP 129 Down setup to LSG to clean socket PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
127 PCS OCAP 130 DOWN TO PE FOR VERIFICATION T#334 above 1% PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
128 PCS OCAP 131 Duplicate ECID. Please inform PLS. PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
129 PCS OCAP 132 Duplicate Unit XY Detected, Contact PLS/PE PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
130 PCS OCAP 133 Duplicate XY, STOP & CONTACT PE/PLS PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
131 PCS OCAP 134 Duplicate XY Unit, Call PLS/PE PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
132 PCS OCAP 135 ECID check fail , handler stuck unit PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
133 PCS OCAP 136 ECID Checking repeat , please check if handler stuck PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
134 PCS OCAP 137 ECID Check Monitor PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
135 PCS OCAP 138 ECID Check Monitor PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
136 PCS OCAP 139 ECID FAIL PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
137 PCS OCAP 140 ECID repeat PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
138 PCS OCAP 141 E-corr alpha testing at UFX28 PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
139 PCS OCAP 142 eCorr Alph Testing PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
140 PCS OCAP 143 eCorr Critical PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
141 PCS OCAP 144 eCorr Warning Trigger! 1) Stop lot & perform manual correlation. PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
142 PCS OCAP 145 Edge die checking - Map Shift PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
143 PCS OCAP 146 Efuse Error. Need to kill smartest and reload program. PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
144 PCS OCAP 147 Endlot / Abort Testing call PE PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
145 PCS OCAP 148 Endlot and Abort Testing call PE PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
146 PCS OCAP 149 Follow Generic OCAP PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
147 PCS OCAP 150 Follow Generic OCAP PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
148 PCS OCAP 151 For monitoring purposes. No action required. PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
149 PCS OCAP 152 Generic WS S2S Trigger OCAP for LSG : 1st Trigger, Online cleaning / Re-align / Add OD, 2nd Trigger PM PC / Change PC, 3rd Trigger Change PIB, 4th Trigger Down to TSG PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
150 PCS OCAP 153 Generic WS S2S Trigger OCAP for LSG : 1st Trigger, Online cleaning / Re-align / Add OD, 2nd Trigger PM PC / Change PC, 3rd Trigger Change PIB, 4th Trigger Down to TSG PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
151 PCS OCAP 154 Generic WS S2S Trigger OCAP for LSG : 1st Trigger, Online cleaning / Re-align / Add OD, 2nd Trigger PM PC / Change PC, 3rd Trigger Change PIB, 4th Trigger Down to TSG PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
152 PCS OCAP 155 Generic WS S2S Trigger OCAP for LSG : 1st Trigger, Online cleaning / Re-align / Add OD, 2nd Trigger PM PC / Change PC, 3rd Trigger Change PIB/Pogo tower, 4th Trigger Down to TSG PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
153 PCS OCAP 156 Generic WS S2S Trigger OCAP for LSG : 1st Trigger, Online cleaning / Re-align / Add OD, 2nd Trigger PM PC / Change PC, 3rd Trigger Change PIB/Pogo tower, 4th Trigger Down to TSG PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
154 PCS OCAP 157 haha PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
155 PCS OCAP 158 hard bin 5 critical trigger PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
156 PCS OCAP 159 hard bin 8 critical trigger PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
157 PCS OCAP 160 High bottom socket conty fallout, pls clean bottom socket with Mipox and air gun blow. PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
158 PCS OCAP 161 High bottom socket conty fallout, pls clean the bottom socket with Mipox and air gun blow. PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
159 PCS OCAP 162 High conty fallout!!! 1. Pls check and ensure only ISC socket used for production. 2. Clean socket with air gun blow only or 3. Send socket to PM if problem still persist 4. DO NOT CLEAN SOCKET WITH BRUSH/MIPOX!!! PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
160 PCS OCAP 163 High conty fallout!!! Pls check is auto Mipox cleaning enabled. Pls perform 5x mipox cleaning under contact mode if auto cleaning already enabled, pls change socket if problem persist. DO NOT clean socket with brush. PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
161 PCS OCAP 164 High Conty OCAP: 1)Check probemarks of the kelvin pins - outer should be hitting the pad solid 2)SWAP SOCKET, CHANGE IF FAILURE FOLLOW THE SITE 3)DOWN BAD SOCKET FOR INVESTIGATION PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
162 PCS OCAP 165 High Conty OCAP: 1) Clean socket . If the same result 2) Replace with lower insertion spare socket. If the same result 2) Change other good loadboard/DUTCARD, if result the same 3) Down to TSG for tester repair PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
163 PCS OCAP 166 High Conty OCAP: 1)swap socket form good site or replace with lower insertion spare socket. If the same result 2)Change other good loadboard, if result the same 3)Down to TSG for tester repai PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
164 PCS OCAP 167 High Conty OCAP: 1)swap socket form good site or replace with lower insertion spare socket. If the same result 2)Change other good loadboard, if result the same 3)Down to TSG for tester repair PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
165 PCS OCAP 168 High Conty OCAP: 1)swap socket form good site or replace with lower insertion spare socket. If the same result 2)Change other good loadboard, if result the same 3)Down to TSG for tester repair PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
166 PCS OCAP 169 High Conty OCAP: If MTF is on T#83084, continue running 1)swap socket form good site or replace with lower insertion spare socket. If the same result 2)Change other good loadboard, if result the same 3)Down to TSG for tester repair PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
167 PCS OCAP 170 High Conty yield gap. Perform OCAP. Check socket, then LB, then tester. PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
168 PCS OCAP 171 High Funct fallout!!! 1. Pls check and ensure only ISC socket used for production. 2. Clean socket with air gun blow only or 3. Send socket to PM if problem still persist 4. DO NOT CLEAN SOCKET WITH BRUSH/MIPOX!!! PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
169 PCS OCAP 172 High Funct fallout!!! Pls check is auto Mipox cleaning enabled. Pls perform 5x mipox cleaning under contact mode if auto cleaning already enabled, pls change socket if problem persist. DO NOT clean socket with brush. PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
170 PCS OCAP 173 High Rejects OCAP: 1) Clean Socket 2) Swap / Change Socket PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
171 PCS OCAP 174 High Rejects OCAP: 1) Clean Socket with MiPox 2) Swap / Change Socket PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
172 PCS OCAP 175 High SB201 fallout, pls clean bottom socket with Mipox and air gun blow. PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
173 PCS OCAP 176 High SB201 fallout, pls clean the bottom socket with Mipox and air gun blow. PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
174 PCS OCAP 177 High site yield gap. Perform OCAP. Check socket, then LB, then tester. PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
175 PCS OCAP 178 High site yield gap. Perform OCAP. Check socket, then LB, then tester. PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
176 PCS OCAP 179 High Site yield gap, perform OCAP on the site with lower yield. Clean or replace socket, then LB, PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
177 PCS OCAP 180 High Site yield gap, perform OCAP on the site with lower yield. Clean or replace socket, then LB, the debug tester. PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
178 PCS OCAP 181 High tapbist fallout!!! 1. Pls check and ensure only ISC socket used for production. 2. Clean socket with air gun blow only or 3. Send socket to PM if problem still persist 4. DO NOT CLEAN SOCKET WITH BRUSH/MIPOX!!! PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
179 PCS OCAP 182 High tapbist fallout!!! Pls check is auto Mipox cleaning enabled. Pls perform 5x mipox cleaning under contact mode if auto cleaning already enabled, pls change socket if problem persist. DO NOT clean socket with brush. PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
180 PCS OCAP 183 High temperature test fallout!!! 1. Pls check the temperature setup correctly as per PDMS 2. Pls check UI report on the temperature reading to see the failure is due to marginal or not,can seek advice from PE/PLS if not sure how to check 3. If it is marginal, Only allow to adjust temperature offset at handler from (-3'c to 3'c) depend on the failure due to marginal low or marginal high 4. Seek advice from HSG if the problem still persist. PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
181 PCS OCAP 184 High temperature test fallout!!!Pls check the handler temperature setting done correctly as per PDMS. If it done correctly, pls offset temperature setting (~1'C to 2'C) if failure due to marginal high. PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
182 PCS OCAP 185 High THD failure OCAP (For COLD temperature) 1) Defrost handler and CHANGE SOCKET 2) Change MIPOX Auto Cleaning paper for both sites High THD failure OCAP (For ROOM and HOT) 1) CHANGE SOCKET and MIPOX Auto Cleaning paper PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
183 PCS OCAP 186 High top socket conty fallout, pls clean the top socket with nylon brush and air gun blow PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
184 PCS OCAP 187 High top socket conty fallout, pls clean top socket with nylon brush and air gun blow PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
185 PCS OCAP 188 High TRIM failures: 1)swap socket form good site or replace with lower insertion spare socket. If the same result 2)Change other good loadboard, if result the same 3)Disable site ASAP PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
186 PCS OCAP 189 High yield loss, pls clean bottom socket with Mipox and Top socket with nylon brush PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
187 PCS OCAP 190 Historical Setup Issue 1. Clean Socket 2. Change socket 3. Change load board 4. Trigger PLS/PE to check FAB issue PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
188 PCS OCAP 191 Inform PLS to check. PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
189 PCS OCAP 192 KS_eCorr Warning Triggered!! Stop production. PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
190 PCS OCAP 193 Local Fail Monitor trigger PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
191 PCS OCAP 194 Local Site Yield monitor trigger PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
192 PCS OCAP 195 Low Yield!!! 1. Pls check and ensure only ISC socket used for production. 2. Pls clean socket with air gun blow only if issue was due to Hbin4/Hbin5/Hbin6 and send socket to PM if problem still persist 3. Pls check the handler temperature setting If the failure due to Hbin3, offset allowed from (-3'c to 3'c) if failure due to marginal 4. DO NOT CLEAN SOCKET WITH BRUSH/MIPOX!!! PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
193 PCS OCAP 196 Low Yield < 75%!!! Pls clean socket/verify socket on the low yield site. PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
194 PCS OCAP 197 LOW YIELD < 80% OCAP: 1) Clean Socket 2) Swap / Change Socket 3) Change Loadboard 4) Tester Verification PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
195 PCS OCAP 198 LOW YIELD < 80% OCAP: 1) Clean Socket/ socket PM 2) Swap / Change Socket 3) Change Loadboard 4) Tester Verification PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
196 PCS OCAP 199 Low Yield < 80%!!! Pls clean socket/verify socket on the low yield site. PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
197 PCS OCAP 200 LOW YIELD < 85% OCAP: 1) Clean Socket 2) Swap / Change Socket 3) Change Loadboard 4) Tester Verification PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
198 PCS OCAP 201 Low Yield < 85%!!! Pls clean socket/verify socket. PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
199 PCS OCAP 202 Low Yield < 85%!!! Pls clean socket/verify socket on the low yield site. PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
200 PCS OCAP 203 LOW YIELD < 87% OCAP: 1) Clean Socket 2) Swap / Change Socket 3) Change Loadboard 4) Tester Verification PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
201 PCS OCAP 204 Low Yield < 88%!!! Pls clean socket/verify socket on the low yield site. PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
202 PCS OCAP 205 LOW YIELD < 90% OCAP: 1) Clean Socket 2) Swap / Change Socket 3) Change Loadboard 4) Tester Verification PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
203 PCS OCAP 206 Low Yield < 90%!!! Pls clean socket/verify sock PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
204 PCS OCAP 207 Low Yield < 90%!!! Pls clean socket/verify socket. PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
205 PCS OCAP 208 Low Yield < 90%!!! Pls clean socket/verify socket. PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
206 PCS OCAP 209 LOW YIELD OCAP: 1) Clean Socket 2) Swap / Change Socket 3) Change Loadboard 4) Tester Verification PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
207 PCS OCAP 210 Low Yield!!! Pls check is auto cleaning enabled if the fail was due to Hbin 5/Hbin 4. Pls check the handler temperature setting If the failure due to Hbin 3. PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
208 PCS OCAP 211 LSG to do LB OCAP PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
209 PCS OCAP 212 LSG to do socket OCAP PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
210 PCS OCAP 213 LSG tp do socket OCAP PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
211 PCS OCAP 214 Map SHIFT ( target die) Bin8 PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
212 PCS OCAP 215 NCF 2 PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
213 PCS OCAP 216 NCF CF monitor PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
214 PCS OCAP 217 NCF failure PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
215 PCS OCAP 218 NCF TRIGGER PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
216 PCS OCAP 219 NCF TRIGGER PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
217 PCS OCAP 220 No good units tested OCAP: 1) Clean Socket 2) If after clean socket still the same, please ENDLOT 3) Run CORR to check setup PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
218 PCS OCAP 221 NON-CONSECUTIVE CONTY > 2% OCAP: 1) Clean Socket 2) Swap / Change Socket 3) Change Loadboard 4) Tester Verification PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
219 PCS OCAP 222 NON-CONSECUTIVE CONTY > 3% OCAP: 1) Clean Socket 2) Swap / Change Socket 3) Change Loadboard 4) Tester Verification PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
220 PCS OCAP 223 non retest critical bin fail. Please check setup. PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
221 PCS OCAP 224 Non-Retest Reject (HBin6) 1) Stop Test, Endlot Testing and Run Corr to Confirm No Setup Issue. 2) If Corr Run Pass, please continue testing. If Fail down to corr fail PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
222 PCS OCAP 225 Not critical PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
223 PCS OCAP 226 ocap PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
224 PCS OCAP 227 ocap PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
225 PCS OCAP 228 OCAP: 1)Abort lot and run corr to verify setup 2a)If corr fail on the same sbin and tests, then down setup to LSG to fix the setup first 2b)If corr pass, MFG to select other lot with different FAB ID PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
226 PCS OCAP 229 OCAP: 1) Call PE /PLS PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
227 PCS OCAP 230 OCAP: 1) Change socket, 2) Optimize the setup 3) Disable site PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
228 PCS OCAP 231 OCAP: 1) Change socket to low insertion one 2) send affected socket for PM. PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
229 PCS OCAP 232 OCAP: 1.Check affected site socket 2.Check VM 3.Swap Socket 4.Change Socket 5. disable site if failure still exits PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
230 PCS OCAP 233 ocap 1) Check handler 2) Contact TSG PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
231 PCS OCAP 234 OCAP: 1) Check LY site, 2) Change socket 3) Disable sites PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
232 PCS OCAP 235 OCAP: 1) Check LY site 2) Change socket, 3) Optimize the setup 4) Disable site PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
233 PCS OCAP 236 OCAP: 1. Check Socket Insertion & Clean Socket 2.Swap Socket -- check if failure moves 3. Change Socket 4.Change Loadboard PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
234 PCS OCAP 237 OCAP:1) Clean Socket2) Change or Swap Socket3) Change Loadboard4) Tester Repair PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
235 PCS OCAP 238 OCAP: 1.Clean Socket 2.Clean Socket 3.Change Socket if the affected site is still < 90% 4. Shut down the affected site. PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
236 PCS OCAP 239 OCAP: 1.Clean Socket 2.Clean Socket & contactor 3.Change Socket 4. Shut down the affected site. PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
237 PCS OCAP 240 OCAP:1.) Clean socket, 2.),Replace socket,3.) Change loadboard, 4.) Call PE PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
238 PCS OCAP 241 OCAP: 1) Clean Socket 2) Swap / Change Socket PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
239 PCS OCAP 242 OCAP: 1) Clean Socket 2) Swap / Change Socket PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
240 PCS OCAP 243 OCAP: 1) Clean Socket 2) Swap / Change Socket PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
241 PCS OCAP 244 OCAP: 1) Clean Socket 2) Swap / Change Socket 3) Change Loadboard PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
242 PCS OCAP 245 OCAP: 1) Clean Socket 2) Swap / Change Socket 3) Change Loadboard PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
243 PCS OCAP 246 OCAP: 1) Clean Socket 2) Swap / Change Socket 3) Change Loadboard PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
244 PCS OCAP 247 OCAP: 1) Clean Socket 2) Swap / Change Socket 3) Change Loadboard PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
245 PCS OCAP 248 OCAP: 1) Clean Socket 2) Swap / Change Socket 3) Change Loadboard 4) Tester Verification PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
246 PCS OCAP 249 OCAP: 1) Clean Socket 2) Swap / Change Socket 3) Change Loadboard 4) Tester Verification PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
247 PCS OCAP 250 OCAP: 1) Clean Socket 2) Swap / Change Socket 3) Change Loadboard 4) Tester Verification PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
248 PCS OCAP 251 OCAP: 1) Clean Socket 2) Swap / Change Socket 3) Change Loadboard 4) Tester Verification PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
249 PCS OCAP 252 OCAP: 1) Clean Socket 2) Swap / Change Socket 3) Change Loadboard 4) Tester Verification PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
250 PCS OCAP 253 OCAP: 1) Clean Socket 2) Swap / Change Socket 3) Change Loadboard 4) Tester Verification PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
251 PCS OCAP 254 OCAP: 1) Clean Socket 2) Swap / Change Socket 3) Change Loadboard 4) Tester Verification PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
252 PCS OCAP 255 OCAP: 1) Clean Socket 2) Swap / Change Socket 3) Change Loadboard 4) Tester Verification PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
253 PCS OCAP 256 OCAP: 1) Clean Socket 2) Swap / Change Socket 3) Change Loadboard 4) Tester Verification PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
254 PCS OCAP 257 OCAP: 1) Clean Socket 2) Swap / Change Socket 3) Disable site PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
255 PCS OCAP 258 OCAP: 1) Clean Socket 2) Swap / Change Socket 3) Perform ESD check on tester/handler 4) Disable site PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
256 PCS OCAP 259 Ocap: 1) clean socket 2) swap socket 3) change socket PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
257 PCS OCAP 260 Ocap: 1) clean socket 2) swap socket 3) change socket PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
258 PCS OCAP 261 OCAP: 1.Clean Socket 2.Swap Socket -- check if failure moves 3. Change Socket 4.Change Loadboard PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
259 PCS OCAP 262 OCAP: 1.Clean Socket 2.Swap Socket -- check if failure moves 3. Change Socket 4.Change Loadboard PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
260 PCS OCAP 263 OCAP: 1.Clean Socket 2.Swap Socket -- check if failure moves 3. Change Socket 4.Change Loadboard PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
261 PCS OCAP 264 OCAP: 1.Clean Socket 2.Swap Socket -- check if failure moves 3. Change Socket 4.Change Loadboard PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
262 PCS OCAP 265 OCAP: 1.Clean Socket 2.Swap Socket -- check if failure moves 3. Change Socket 4.Change Loadboard PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
263 PCS OCAP 266 OCAP: 1.Clean Socket 2.Swap Socket -- check if failure moves 3. Change Socket 4.Shut down the site PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
264 PCS OCAP 267 OCAP: 1.Clean Socket 2.Swap Socket -- check if failure moves 3. Change Socket 4.Shut down the site PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
265 PCS OCAP 268 OCAP: 1)Clean socket or swap from other good sites PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
266 PCS OCAP 269 OCAP: 1) Clean Socket with MIPOX 2) Send socket for PM 3) Swap / Change Socket 4) Change Loadboard PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
267 PCS OCAP 270 OCAP: 1) Clean Socket with MIPOX 2) Send socket for PM 3) Swap / Change Socket 4) Change Loadboard PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
268 PCS OCAP 271 OCAP: 1) Clean Socket with MiPox 2) Swap / Change Socket PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
269 PCS OCAP 272 OCAP: 1) Endlot and Delete Program 2) Startlot and Monitor if SB26 in Site1 Recovers 3) Clean/Swap Socket 4) Delete Program and Change LB PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
270 PCS OCAP 273 OCAP: 1) end lot and kill smartest (efuse fail) PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
271 PCS OCAP 274 OCAP: 1) Endlot and Run Corr to Check Setup PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
272 PCS OCAP 275 OCAP: 1)If trigger because of HBIN9 (T#754), please clean socket and continue run if not follow item 2) to 4) 2)swap socket form good site or replace with lower insertion spare socket. If the same result 3)Change other good loadboard, if result the same 4)Down to TSG for tester repair PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
273 PCS OCAP 276 OCAP: 1) Please Clean Socket 2) If after Clean Socket still the same, LY/High Reject Please Swap / Change Socket 3) Change Loadboard 4) Tester Verification PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
274 PCS OCAP 277 OCAP: 1) Please Clean Socket 2) If after Clean Socket still the same, LY/High Reject Please Swap / Change Socket 3) Change Loadboard 4) Tester Verification PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
275 PCS OCAP 278 OCAP: 1) Running yield <80% please endlot and run corr PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
276 PCS OCAP 279 OCAP: 1) Running Yield Below 70%, please endlot and Run Corr to check setup. PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
277 PCS OCAP 280 OCAP: 1) Running Yield Below 75%, Please Down to Clean Socket 2) If still LY, Endlot and Run Corr. PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
278 PCS OCAP 281 OCAP: 1) Sent socket for PM 2) Change Socket PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
279 PCS OCAP 282 OCAP: 1)swap socket form good site or replace with lower insertion spare socket. If the same result 2)Change other good loadboard, if result the same 3)Down to TSG for tester repair PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
280 PCS OCAP 283 OCAP: 1)swap socket form good site or replace with lower insertion spare socket. If the same result 2)Change other good loadboard, if result the same 3)Down to TSG for tester repair PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
281 PCS OCAP 284 OCAP: Change Socket. Optimize setup. PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
282 PCS OCAP 285 OCAP Critical ! 1). check tester 2). check handler 3). check all PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
283 PCS OCAP 286 OCAP FOR CONSECUTIVE FAIL: 1. Clean Socket 2. Swap Socket - check if failure follows. 3. Change Socket 4. Change Loadboard 5. Tester Verification (disable affected site first if need to schedule repair). PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
284 PCS OCAP 287 OCAP FOR MS: 1. Check for piggy back units on the socket site 2. Call PE/PLS to check STDF if any piggy good units tested PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
285 PCS OCAP 288 OCAP for S2S Fail:1. Clean Socket2. Swap Socket - check if failure follows.3. Change Socket4. Change Loadboard5. Tester Verification (disable affected site first if need to schedule repair). PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
286 PCS OCAP 289 OCAP Site2Site Delta ALarm!!! PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
287 PCS OCAP 290 OCAP:trigger PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
288 PCS OCAP 291 OCAP:trigger PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
289 PCS OCAP 292 OCAP triggered PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
290 PCS OCAP 293 OCAP WARNING PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
291 PCS OCAP 294 Parametric CPK monitoring UAT. No action required. PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
292 PCS OCAP 295 Parametric Monitoring UAT. No OCAP required. PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
293 PCS OCAP 296 Parametric Monitor test PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
294 PCS OCAP 297 Parametric Test Monitoring UAT. No OCAP required. PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
295 PCS OCAP 298 Parametric Test UAT. No OCAP required PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
296 PCS OCAP 299 Parametric UAT. No OCAP action required PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
297 PCS OCAP 300 Parametric UAT - Test CP Monitoring. No action required. Continue Test. PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
298 PCS OCAP 301 PE to check PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
299 PCS OCAP 302 PLEASE CLEAN / VERIFY SOCKETS PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
300 PCS OCAP 303 Please down to clean socket PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
301 PCS OCAP 304 Please follow OCAP Procedure for LY and consecutive failure (as documented in PDMS) PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
302 PCS OCAP 305 Please follow OCAP Procedure for LY and consecutive failure (as documented in PDMS) PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
303 PCS OCAP 306 Please perform OCAP or disable affected site if cant fix. PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
304 PCS OCAP 307 Please send socket for PM. once Bin6 > 5%. PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
305 PCS OCAP 308 Please send socket PUS2904/5 for PM. once Bin6 > 2%. PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
306 PCS OCAP 309 POSSIBLE CAUSING MISTRIM 1) STOP TEST, REMOVE SOCKET AND SEND FOR OFFLINE PM 2) CHANGE SOCKET IF STILL FAIL AFTER OFFLINE PM PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
307 PCS OCAP 310 POSSIBLE CAUSING MISTRIM 1) STOP TEST, REMOVE SOCKET AND SEND FOR OFFLINE PM 2) CHANGE SOCKET IF STILL FAIL AFTER OFFLINE PM PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
308 PCS OCAP 311 Possible causing MISTRIM 1) Stop test,, Remove socket and send for offline PM 2) Change Socket if still fail after offline PM 3) Change LB if still fail after change socket 4) Off site if still fail after change LB PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
309 PCS OCAP 312 POSSIBLE CAUSING MISTRIM 1) STOP TEST, REMOVE SOCKET AND SEND FOR OFFLINE PM 2) CHANGE SOCKET IF STILL FAIL AFTER OFFLINE PM 3) CHANGE LOADBOARD 4) DOWN TO TSG FOR TESTER REPAIR PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
310 PCS OCAP 313 result 2)Change other good loadboard, if result the same 3)Down to TSG for tester repair PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
311 PCS OCAP 314 Rule Violated! PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
312 PCS OCAP 315 Run CORR, Socket / LB OCAP PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
313 PCS OCAP 316 S2S > 10%. Clean socket, change socket of LY site. PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
314 PCS OCAP 317 S2S > 5%. Clean socket, change socket of LY site. PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
315 PCS OCAP 318 S2S > 8%, please check if any plunger induce issue, else clean socket, if cleaning don't help, change socket and clean LB pad. PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
316 PCS OCAP 319 S2S & CBL OCAP: 1)Clean socket or swap from other good sites PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
317 PCS OCAP 320 S2S & CBL OCAP: 1)Clean socket or swap from other good sites PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
318 PCS OCAP 321 S2S & CBL OCAP: 1)Clean socket or swap from other good sites 2) if low yield site is t#1122(Current Limit) CLEAN with MIPOX socket pins. PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
319 PCS OCAP 322 S2S & CBL OCAP: 1)swap socket form good site or replace with lower insertion spare socket. If the same result 2)Change other good loadboard, if result the same 3)Down to TSG for tester repair PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
320 PCS OCAP 323 S2S & CBL OCAP: 1)swap socket form good site or replace with lower insertion spare socket. If the same result 2)Change other good loadboard, if result the same 3)Down to TSG for tester repair PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
321 PCS OCAP 324 S2S & CBL OCAP: 1)swap socket form good site or replace with lower insertion spare socket. If the same result 2)Change other good loadboard, if result the same 3)Down to TSG for tester repair PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
322 PCS OCAP 325 S2S & CBL OCAP: 1)swap socket form good site or replace with lower insertion spare socket. If the same result 2)if low yield site is t#1122(Current Limit) - SEND FOR PM OR CHANGE SOCKET/s 3)Change other good loadboard, if result the same 4)Down to TSG for tester repair PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
323 PCS OCAP 326 S2S & CBL OCAP: 1)swap socket from good site or replace with lower insertion spare socket. If the same result 2)Change other good loadboard, if result the same 3)Down to TSG for tester repair PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
324 PCS OCAP 327 S2S OCAP: 1. Clean Socket of Low Yield Site PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
325 PCS OCAP 328 S2S OCAP: 1. Clean Socket of Low Yield Site 2. Swap Socket with Best Yield Site(Change bad socket if failure follow) 3. Change Socket causing the Low Yield 4. Perform LB OCAP PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
326 PCS OCAP 329 S2S OCAP: 1) If there is high S2S due to T#60 ADCHiINL1V6 and T#61 ADCLoINL1V6 NO OCAP NEEDED 2) If high s2s due to other failure do socket OCAP (swap/change socket) 3) If same do LB OCAP PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
327 PCS OCAP 330 S2S OCAP: 1)Quick fix s2s clean/swap/change 2)If fail Bin8 t#13159/13160/23159/23160 perform agressive AUTO CLEANING 3)No quick undocking at COLD temp! PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
328 PCS OCAP 331 S2S OCAP: 1)Quick fix s2s clean/swap socket 2)If fail Bin8 t#13159/13160/23159/23160 change socket of low yield site and replace MIPOX paper also if dirty. 3)No quick undocking at COLD temp! PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
329 PCS OCAP 332 S2S OCAP: 1)swap socket form good site or replace with lower insertion spare socket. If the same result 2)Change other good loadboard, if result the same 3)Down to TSG for tester repair PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
330 PCS OCAP 333 S2S OCAP: 1)swap socket form good site or replace with lower insertion spare socket. If the same result 2)Change other good loadboard, if result the same 3)Down to TSG for tester repair PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
331 PCS OCAP 334 S2S Yield Gap >12%, please sent PC for PM or change another PC PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
332 PCS OCAP 335 SB6001>5%, please check whether setup or wafer relate issue. PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
333 PCS OCAP 336 SB6001>5%, please check whether setup or wafer relate issue. Yield <93%, please check setup. PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
334 PCS OCAP 337 Setup under monitor (for engineering reference) PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
335 PCS OCAP 338 Site-to-Site >10% please do following OCAP: 1) Endlot and Delete Program 2) Run Corr to check setup 3) Clean/Swap Socket 4) Delete Program and Change LB PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
336 PCS OCAP 339 Site-to-Site >10% please do following OCAP: 1) Endlot and Delete Program 2) Startlot and Monitor if SB26 in Site1 Recovers 3) Clean/Swap Socket 4) Delete Program and Change LB PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
337 PCS OCAP 340 site to site >12% Clean socket & check insertion PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
338 PCS OCAP 341 Site-to-site warning message PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
339 PCS OCAP 342 Site-to-Site Yield > 10% OCAP: 1) Clean Socket 2) Swap / Change Socket 3) Change Loadboard 4) Tester Verification PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
340 PCS OCAP 343 Site-to-Site Yield > 5% PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
341 PCS OCAP 344 Site yield delta >10%!!! Pls clean socket/verify socket on the low yield site. PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
342 PCS OCAP 345 Site yield delta >10%!!! Pls clean socket/verify socket on the low yield site. PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
343 PCS OCAP 346 Site yield delta >10%!!! Pls clean top socket with nylon brush and bottom socket with the Mipox on the yield site. PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
344 PCS OCAP 347 Site yield delta >5%!!! Pls clean socket/verify socket on the low yield site. PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
345 PCS OCAP 348 Site yield delta >8%!!! Pls clean socket/verify socket on the low yield site. PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
346 PCS OCAP 349 Site Yield trigger PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
347 PCS OCAP 350 Socket/LB PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
348 PCS OCAP 351 Socket/LB OCAP PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
349 PCS OCAP 352 Socket/LB OCAP PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
350 PCS OCAP 353 Socket/LB/Tester OCAP PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
351 PCS OCAP 354 Socket/Loadboard OCAP PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
352 PCS OCAP 355 Socket OCAP PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
353 PCS OCAP 356 stuck unit PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
354 PCS OCAP 357 test PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
355 PCS OCAP 358 test PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
356 PCS OCAP 359 test count fail trigger PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
357 PCS OCAP 360 Tester PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
358 PCS OCAP 361 Test Freeze Detected! PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
359 PCS OCAP 362 Test Freeze Detected! PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
360 PCS OCAP 363 Test Freeze triggered!!! PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
361 PCS OCAP 364 testing PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
362 PCS OCAP 365 testing PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
363 PCS OCAP 366 testing! PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
364 PCS OCAP 367 Testing eCorr after upgrade PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
365 PCS OCAP 368 Testing OCAP PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
366 PCS OCAP 369 test number x,y repeat PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
367 PCS OCAP 370 Test OCAP PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
368 PCS OCAP 371 To Monitor Test T#754 1) Please clean socket and continue run PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
369 PCS OCAP 372 Total Parametric Test CP Monitor For All Units Triggered PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
370 PCS OCAP 373 Trigger ! PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
371 PCS OCAP 374 Trigger > 3, change LB and sockets. Send back old for PM. PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
372 PCS OCAP 375 Trigger > 3, change LB and sockets. Send back socket for PM. PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
373 PCS OCAP 376 Trigger > 3 times, Clean or replace socket, then LB, the debug tester. please shut down the affected site due to tester/handler pending fix. PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
374 PCS OCAP 377 Trigger > 3 times, Clean or replace socket, then LB, the debug tester. please shut down the affected site due to tester/handler pending fix. PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
375 PCS OCAP 378 Trigger > 3 times, please change sockets. PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
376 PCS OCAP 379 Trigger > 3 times, please shut down the affected site due to tester/handler pending fix. PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
377 PCS OCAP 380 Trigger > 3 times, please shut down the affected site due to tester/handler pending fix. PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
378 PCS OCAP 381 TRIGGERED: 20 Consecutive Failure OCAP: 1) Clean Socket 2) Swap / Change Socket 3) Change Loadboard 4) Tester Verification PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
379 PCS OCAP 382 TRIGGERED: 5 Consecutive Conty Failure OCAP: 1) Clean Socket 2) Swap / Change Socket 3) Change Loadboard 4) Tester Verification PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
380 PCS OCAP 383 TRIGGERED CONSECUTIVE CONTY > 5 OCAP: 1) Clean Socket 2) Swap / Change Socket 3) Change Loadboard 4) Tester Verification PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
381 PCS OCAP 384 TRIGGERED CONSECUTIVE FAILURE > 20 OCAP: 1) Clean Socket 2) Swap / Change Socket 3) Change Loadboard 4) Tester Verification PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
382 PCS OCAP 385 TRIGGERED CONTY > 2% OCAP: 1) Clean Socket 2) Swap / Change Socket 3) Change Loadboard 4) Tester Verification PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
383 PCS OCAP 386 TRIGGERED: Non-Consecutive conty > 2% OCAP:1) Clean Socket2) Swap / Change Socket3) Change Loadboard4) Tester Verification PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
384 PCS OCAP 387 TRIGGERED: S2S Yield > 5% OCAP: 1) Clean Socket 2) Swap / Change Socket 3) Change Loadboard 4) Tester Verification PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
385 PCS OCAP 388 TRIGGERED SITE YIELD GAP > 10% PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
386 PCS OCAP 389 TRIGGERED SITE YIELD GAP > 5% PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
387 PCS OCAP 390 TRIGGERED SITE YIELD GAP > 5% OCAP: 1) Clean Socket 2) Swap / Change Socket 3) Change Loadboard 4) Tester Verification PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
388 PCS OCAP 391 TRIGGERED SITE YIELD GAP > 8% PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
389 PCS OCAP 392 Trigger Wafer Alignment Target Dies Checking HBin8 ( map Shift ) PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
390 PCS OCAP 393 Trigger Wafer alignment target Surrounding dies Checking HBin8 ( map Shift ) PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
391 PCS OCAP 394 Trigger Wafer Edge Die Bin Delta Checking HBin8 ( map Shift ) PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
392 PCS OCAP 395 Trim Check Failure : Change PIB/PCard PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
393 PCS OCAP 396 TUTS Trigger Alarm EVAL PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
394 PCS OCAP 397 uat PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
395 PCS OCAP 398 uat PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
396 PCS OCAP 399 uat PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
397 PCS OCAP 400 uat PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
398 PCS OCAP 401 uat PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
399 PCS OCAP 402 uat PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
400 PCS OCAP 403 uat PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
401 PCS OCAP 404 unit repeat PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
402 PCS OCAP 405 Wafer having Low Yield issue. Perform OCAP. PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
403 PCS OCAP 406 warning PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
404 PCS OCAP 407 WARNING DEVICE IS FAILING NON RETEST BIN6!! : DO THE FOLLOWING! 1. SWAP SOCKET FROM HIGH REJECT SITE WITH THE OTHER GOOD SITE 2. IF BIN6 FOLLOW THE BAD SOCKET -> CHANGE WITH NEW SOCKET AND RECORD THE BAD SOCKET ID 3. IF BIN6 STAY AT THE SAME SITE --> DISABLE HIGH BIN6 SITE PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
405 PCS OCAP 408 WARNING DEVICE IS FAILING NON RETEST BIN6!! : DO THE FOLLOWING! 1. SWAP SOCKET FROM HIGH REJECT SITE WITH THE OTHER GOOD SITE 2. IF BIN6 FOLLOW THE BAD SOCKET -> CHANGE WITH NEW SOCKET AND RECORD THE BAD SOCKET ID. UPDATE TUTS FOR ALL ACTION DONE 3. IF BIN6 STAY AT THE SAME SITE --> DISABLE HIGH BIN6 SITE PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
406 PCS OCAP 409 WARNING DEVICE IS MISTRIMMED : STOP TESTING! DO THE FOLLOWING 1. FORCE QA LOT - END LOT and RUN CORRELATION UNITS TO VERIFY SET UP 2. FIX SET UP IF CORR FAIL 3. TRIGGER PE OR PLS PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
407 PCS OCAP 410 WARNING DEVICE IS MISTRIMMED : STOP TESTING! DO THE FOLLOWING 1. FORCE QA LOT - END LOT and RUN CORRELATION UNITS TO VERIFY SET UP 2. IF CORR FAIL CHANGE LOAD BOARD 3. TRIGGER PE OR PLS PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
408 PCS OCAP 411 WARNING DEVICE IS MISTRIMMED : STOP TESTING! DO THE FOLLOWING 1. FORCE QA LOT - END LOT and RUN CORRELATION UNITS TO VERIFY SET UP 2. IF CORR FAIL FIX SET UP OR CHANGE LOAD BOARD 3. TRIGGER PE OR PLS IF CANNOT RECOVER SET UP PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
409 PCS OCAP 412 WARNING DEVICE IS MISTRIMMED : STOP TESTING! DO THE FOLLOWING 1. SWAP HIGH YIELD SITE SOCKET WITH LOW YIELD SITE SOCKET 2. IF LOW YIELD FOLLOW SOCKET, CHANGE BAD SOCKET AND DOWN IN HW ROOM(LOG IN TUTS) 3. IF STILL SAME SITE LOW YIELD AFTER SWAP SOCKET - CHANGE LOADBOARD(LOG IN TUTS) PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
410 PCS OCAP 413 WARNING DEVICE IS MISTRIMMED : STOP TESTING! DO THE FOLLOWING 1. SWAP HIGH YIELD SITE SOCKET WITH LOW YIELD SITE SOCKET 2. IF LOW YIELD FOLLOW SOCKET, CHANGE BAD SOCKET AND DOWN IN HW ROOM(LOG IN TUTS) 3. IF STILL SAME SITE LOW YIELD AFTER SWAP SOCKET - CHANGE LOADBOARD(LOG IN TUTS) 4. IF STILL LOW YIELD, OFF SITE AND INFORM PE PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
411 PCS OCAP 414 WARNING DEVICE IS MISTRIMMED : STOP TESTING! DO THE FOLLOWING 1. SWAP HIGH YIELD SITE SOCKET WITH LOW YIELD SITE SOCKET 2. IF LOW YIELD FOLLOW SOCKET, CHANGE BAD SOCKET AND DOWN IN HW ROOM(LOG IN TUTS) 3. IF STILL SAME SITE LOW YIELD AFTER SWAP SOCKET - CHANGE LOADBOARD(LOG IN TUTS) 4. IF STILL LOW YIELD, OFF SITE AND INFORM PE PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
412 PCS OCAP 415 Warning pop up 1). check tester 2). check handler 3). check all PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
413 PCS OCAP 416 WARNING T#1122 FAILURE SENSITIVE TO CONTACT - NO ONLINE CLEAN NEEDED 1)SEND SOCKET FOR CLEANING WITH MIPOX. 2)CHANGE SOCKET PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
414 PCS OCAP 417 Yield <70%, please do the following OCAP: 1) Clean Socket 2) If after clean socket still the same, please ENDLOT 3) Run CORR to check setup PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
415 PCS OCAP 418 Yield <75%, please do inline socket cleaning PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
416 PCS OCAP 419 Yield <90%, please check setup. PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
417 PCS OCAP 420 Yield <93%, please check setup. PuiPui 20/07/2020
03:22:07 PM 		PuiPui 20/07/2020
03:22:07 PM
418 PCS OCAP 421 Yield issue. Please follow OCAP Procedure for LY (as documented in PDMS)\t PuiPui 20/07/2020
03:22:07 PM 		28/09/2020
02:32:44 PM
419 OEE ee1 1. s1 2. s2 puipui 03/09/2020
01:41:22 PM 		puipui 03/09/2020
03:31:52 PM
420 OEE OCAP 2 Ocap 1 07/09/2020
09:32:09 PM 		07/09/2020
09:32:46 PM
421 OEE Oee OCAP 1 OEE 123 1. <svg class="svg-inline--fa fa-bars fa-w-14" aria-hidden="true" focusable="false" data-prefix="fas" data-icon="bars" role="img" xmlns="http://www.w3.org/2000/svg" viewBox="0 0 448 512" data-fa-i2svg=""><path fill="currentColor" d="M16 132h416c8.837 0 16-7.163 16-16V76c0-8.837-7.163-16-16-16H16C7.163 60 0 67.163 0 76v40c0 8.837 7.163 16 16 16zm0 160h416c8.837 0 16-7.163 16-16v-40c0-8.837-7.163-16-16-16H16c-8.837 0-16 7.163-16 16v40c0 8.837 7.163 16 16 16zm0 160h416c8.837 0 16-7.163 16-16v-40c0-8.837-7.163-16-16-16H16c-8.837 0-16 7.163-16 16v40c0 8.837 7.163 16 16 16z"></path></svg><!-- <i class="fas fa-bars"></i> --> 2. <svg class="svg-inline--fa fa-bars fa-w-14" aria-hidden="true" focusable="false" data-prefix="fas" data-icon="bars" role="img" xmlns="http://www.w3.org/2000/svg" viewBox="0 0 448 512" data-fa-i2svg=""><path fill="currentColor" d="M16 132h416c8.837 0 16-7.163 16-16V76c0-8.837-7.163-16-16-16H16C7.163 60 0 67.163 0 76v40c0 8.837 7.163 16 16 16zm0 160h416c8.837 0 16-7.163 16-16v-40c0-8.837-7.163-16-16-16H16c-8.837 0-16 7.163-16 16v40c0 8.837 7.163 16 16 16zm0 160h416c8.837 0 16-7.163 16-16v-40c0-8.837-7.163-16-16-16H16c-8.837 0-16 7.163-16 16v40c0 8.837 7.163 16 16 16z"></path></svg><!-- <i class="fas fa-bars"></i> --> 3. <svg class="svg-inline--fa fa-bars fa-w-14" aria-hidden="true" focusable="false" data-prefix="fas" data-icon="bars" role="img" xmlns="http://www.w3.org/2000/svg" viewBox="0 0 448 512" data-fa-i2svg=""><path fill="currentColor" d="M16 132h416c8.837 0 16-7.163 16-16V76c0-8.837-7.163-16-16-16H16C7.163 60 0 67.163 0 76v40c0 8.837 7.163 16 16 16zm0 160h416c8.837 0 16-7.163 16-16v-40c0-8.837-7.163-16-16-16H16c-8.837 0-16 7.163-16 16v40c0 8.837 7.163 16 16 16zm0 160h416c8.837 0 16-7.163 16-16v-40c0-8.837-7.163-16-16-16H16c-8.837 0-16 7.163-16 16v40c0 8.837 7.163 16 16 16z"></path></svg><!-- <i class="fas fa-bars"></i> --> 4. <svg class="svg-inline--fa fa-bars fa-w-14" aria-hidden="true" focusable="false" data-prefix="fas" data-icon="bars" role="img" xmlns="http://www.w3.org/2000/svg" viewBox="0 0 448 512" data-fa-i2svg=""><path fill="currentColor" d="M16 132h416c8.837 0 16-7.163 16-16V76c0-8.837-7.163-16-16-16H16C7.163 60 0 67.163 0 76v40c0 8.837 7.163 16 16 16zm0 160h416c8.837 0 16-7.163 16-16v-40c0-8.837-7.163-16-16-16H16c-8.837 0-16 7.163-16 16v40c0 8.837 7.163 16 16 16zm0 160h416c8.837 0 16-7.163 16-16v-40c0-8.837-7.163-16-16-16H16c-8.837 0-16 7.163-16 16v40c0 8.837 7.163 16 16 16z"></path></svg><!-- <i class="fas fa-bars"></i> --> 5. <svg class="svg-inline--fa fa-bars fa-w-14" aria-hidden="true" focusable="false" data-prefix="fas" data-icon="bars" role="img" xmlns="http://www.w3.org/2000/svg" viewBox="0 0 448 512" data-fa-i2svg=""><path fill="currentColor" d="M16 132h416c8.837 0 16-7.163 16-16V76c0-8.837-7.163-16-16-16H16C7.163 60 0 67.163 0 76v40c0 8.837 7.163 16 16 16zm0 160h416c8.837 0 16-7.163 16-16v-40c0-8.837-7.163-16-16-16H16c-8.837 0-16 7.163-16 16v40c0 8.837 7.163 16 16 16zm0 160h416c8.837 0 16-7.163 16-16v-40c0-8.837-7.163-16-16-16H16c-8.837 0-16 7.163-16 16v40c0 8.837 7.163 16 16 16z"></path></svg><!-- <i class="fas fa-bars"></i> --> 6. <svg class="svg-inline--fa fa-bars fa-w-14" aria-hidden="true" focusable="false" data-prefix="fas" data-icon="bars" role="img" xmlns="http://www.w3.org/2000/svg" viewBox="0 0 448 512" data-fa-i2svg=""><path fill="currentColor" d="M16 132h416c8.837 0 16-7.163 16-16V76c0-8.837-7.163-16-16-16H16C7.163 60 0 67.163 0 76v40c0 8.837 7.163 16 16 16zm0 160h416c8.837 0 16-7.163 16-16v-40c0-8.837-7.163-16-16-16H16c-8.837 0-16 7.163-16 16v40c0 8.837 7.163 16 16 16zm0 160h416c8.837 0 16-7.163 16-16v-40c0-8.837-7.163-16-16-16H16c-8.837 0-16 7.163-16 16v40c0 8.837 7.163 16 16 16z"></path></svg><!-- <i class="fas fa-bars"></i> --> 7. <svg class="svg-inline--fa fa-bars fa-w-14" aria-hidden="true" focusable="false" data-prefix="fas" data-icon="bars" role="img" xmlns="http://www.w3.org/2000/svg" viewBox="0 0 448 512" data-fa-i2svg=""><path fill="currentColor" d="M16 132h416c8.837 0 16-7.163 16-16V76c0-8.837-7.163-16-16-16H16C7.163 60 0 67.163 0 76v40c0 8.837 7.163 16 16 16zm0 160h416c8.837 0 16-7.163 16-16v-40c0-8.837-7.163-16-16-16H16c-8.837 0-16 7.163-16 16v40c0 8.837 7.163 16 16 16zm0 160h416c8.837 0 16-7.163 16-16v-40c0-8.837-7.163-16-16-16H16c-8.837 0-16 7.163-16 16v40c0 8.837 7.163 16 16 16z"></path></svg><!-- <i class="fas fa-bars"></i> --> 8. <svg class="svg-inline--fa fa-bars fa-w-14" aria-hidden="true" focusable="false" data-prefix="fas" data-icon="bars" role="img" xmlns="http://www.w3.org/2000/svg" viewBox="0 0 448 512" data-fa-i2svg=""><path fill="currentColor" d="M16 132h416c8.837 0 16-7.163 16-16V76c0-8.837-7.163-16-16-16H16C7.163 60 0 67.163 0 76v40c0 8.837 7.163 16 16 16zm0 160h416c8.837 0 16-7.163 16-16v-40c0-8.837-7.163-16-16-16H16c-8.837 0-16 7.163-16 16v40c0 8.837 7.163 16 16 16zm0 160h416c8.837 0 16-7.163 16-16v-40c0-8.837-7.163-16-16-16H16c-8.837 0-16 7.163-16 16v40c0 8.837 7.163 16 16 16z"></path></svg><!-- <i class="fas fa-bars"></i> --> 09/09/2020
11:33:28 PM 		11/09/2020
09:05:07 AM
422 OEE OEE OCAP 2 1. Step 1 09/09/2020
11:33:55 PM 		09/09/2020
11:33:55 PM
423 OEE OEE 09/09/2020
11:34:40 PM 		09/09/2020
11:34:40 PM
424 PDQ PDQ_OCAP 1 puipui 10/09/2020
11:47:24 AM 		puipui 10/09/2020
11:47:24 AM
425 PdQ pdq 1 09/09/2020
11:50:05 PM 		09/09/2020
11:50:05 PM
426 IVT Connect Visual Inspection High Defect 1. Press Stop button 2. Clean Wash Brush Mop 3. Press Restart button 12/09/2020
12:05:43 AM 		12/09/2020
12:05:43 AM
427 MES Machine Shutdown Unplanned machine shutdown \t 1. Shutdown Machine 2. Inform Technician 3. Technician input finding 13/09/2020
05:54:49 AM 		28/09/2020
02:29:24 PM
428 PCS Lot Check 1te\sti\t\r\nn 2g 1. \r\ntest 2. \ 3. "tes" 4. 2. Clean 5. [0] - 123 6. 1.Check 7. "change socket 'testing' " 8. {study} 9. (SwaP) Socket 10. Change &amp;amp;amp;amp;amp;amp;&amp;amp;amp;amp;amp;amp; Swap 11. }{}{][][)()(&amp;amp;gt;&amp;amp;lt;&amp;amp;gt;&amp;amp;lt;"""'''|||&amp;amp;amp;&amp;amp;amp;&amp;amp;amp;///\\\!===;:*-+^%$#@!~`,.?asd123 12. 3. Monitor 13. "te\sti\t\r\nn" 14. \test 15. 'change socket' 17/09/2020
04:07:49 AM 		01/10/2020
11:56:51 AM
429 PCS sda 01/10/2020
11:03:02 AM 		08/10/2020
06:00:57 PM
430 PCS sda 01/10/2020
11:03:02 AM 		01/10/2020
11:03:02 AM
431 PCS sda 01/10/2020
11:03:03 AM 		01/10/2020
11:03:03 AM
432 OEE sdaa 01/10/2020
03:46:11 PM 		01/10/2020
03:46:11 PM
433 OEE xdcda 01/10/2020
03:46:28 PM 		01/10/2020
03:46:28 PM
434 PCS qqwweqweq 01/10/2020
03:47:34 PM 		01/10/2020
03:47:34 PM
435 OEE ggfffdgdfs 01/10/2020
03:47:54 PM 		puipui 27/10/2020
05:05:31 PM
436 PCS q 08/01/2021
03:27:47 PM 		29/06/2021
12:20:51 PM